Trend

Two fluted tungsten carbide weatherseal groover for use on natural timbers and manmade boards. The cutter is non stick coated to reduce resin build up. For use with smaller routers where application allows. Neatly cuts grooves on doors or frames to ...

Two fluted tungsten carbide weatherseal groover for use on natural timbers and manmade boards. The cutter is non stick coated to reduce resin build up. Neatly cuts grooves on doors or frames to accept a weatherseal. Dimensions: D=36 mm C=3 mm OL=80...

3 degree undercut router bit with shank mounted bearing guide for routing a leading edge on doors to allow a tight fit against jamb. Dimensions: D=24.2 mm C=50 mm A=93 degrees OL=100 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: ...

Attractive edge moulds. A full corner bead can be produced by making a second pass at 90 degrees. Dimensions: D=31.9 mm D2=28.6 mm C=22.5 mm B=16 mm R=7 mm OL=71 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 31.9 Diameter 2 Met...

Attractive edge moulds. A full corner bead can be produced by making a second pass at 90 degrees. Dimensions: D=31.9 mm D2=28.6 mm C=22.5 mm B=16 mm R=7 mm OL=72.5 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Metric: 31.9 Diameter 2 M...

Attractive edge moulds. A full corner bead can be produced by making a second pass at 90 degrees. Dimensions: D=38.1 mm D2=34.7 mm C=26 mm B=16 mm R=9.5 mm OL=74 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 38.1 Diameter 2 Met...

Wide combination moulds for edging table tops and shelves. Dimensions: D=58 mm C=23 mm B=12.7 mm R=7.5 mm R2=6.1 mm OL=72.5 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 58 Cut Length Metric: 23 Overall Length Metric: 72.5 Bea...

Wide combination moulds for edging table tops and shelves. For stationary machines - 16000 RPM recommended speed. Dimensions: D=63 mm C=20 mm B=12.7 mm R=10.5 mm R2=6.5 mm OL=82.5 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 63 ...

Side profile for an attractive handrail. Can be used in conjunction with C191. to produce the handrail top. Dimensions: D=32 mm C=38 mm B=16 mm R=9.5 mm R2=12.5 mm OL=86.5 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 32 Cut L...

One piece tool to increase glueing area for edge to edge joint. Dimensions: D=35 mm C=38.1 mm B=19.1 mm Shank Diameter=1/2 inch OL=90 mm Timber thickness min.=12.7 mm Timber thickness max.=31 mm Shank Diameter: 1/2 Diameter Imperial: 1 3/8 Diamet...

...

Trend Craft Pro 1/2in shank Intumescent strip cutter - 20mm width Two Flute Carbide tips. Cuts the perfect sized slot into door edges and door frames for fast, perfectly flush fitting of intumescent strip. Bearing guide ensures the correct 4mm depth ...

A lip and spur drill for use in a plunge router in conjunction with the Craft Dovetail jigs with doweling attachment. The drill is tungsten carbide tipped for use on natural timbers and manmade boards. This drill is used for shelf supports. The spe...

Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door. To suit 4mm thick strip of 20mm width. Intumescent strip is used to create an effective barrier to both fire and smoke. Choose alternative bearin...

Two fluted tungsten carbide weatherseal groover for use on natural timbers and manmade boards. The cutter is non stick coated to reduce resin build up. Neatly cuts grooves on doors or frames to accept a pile carrier weatherseal. Ideal for parting be...

Two fluted tungsten carbide weatherseal groover for use on natural timbers and manmade boards. The cutter is non stick coated to reduce resin build up. Neatly cuts grooves on doors or frames to accept a pile carrier weatherseal. Ideal for parting be...

Two fluted tungsten carbide weatherseal groover for use on natural timbers and manmade boards. The cutter is non stick coated to reduce resin build up. Neatly cuts grooves on doors or frames to accept a pile carrier weatherseal. Ideal for parting be...

Template thickness should be 5mm thicker than cut length of cutter. Can be used to rout both tenons and housings. Dimensions: D=3/4 inch D=19.1 mm C=11.1 mm B=19.1 mm OL=55 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Imperial: 3/4 D...

Template thickness should be 5mm thicker than cut length of cutter. Can be used to rout both tenons and housings. Dimensions: D=3/4 inch D=19.1 mm C=11.1 mm B=19.1 mm OL=59 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Imperial: 3/4 D...

Recessing cutter for producing double rebates. For producing recesses with a lower rebate. Designed to accept library/bookcase strip. Dimensions: D=13 mm D2=19 mm C= 10 mm C2= 6 mm OL=56 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Met...

Recessing cutter for producing double rebates. For producing recesses with a lower rebate. Designed to accept library/bookcase strip. Specifically designed for Tonk Strip. Dimensions: D=9.5 mm D2=19 mm C=13 mm C2= 6 mm OL=57 mm Shank Diameter=1/2 ...

Trend Craft Pro 1/4in shank recessing cutter - 20mm width Two Flute Carbide tips. Specialist cutter to cut double rebates for fitting Tonk strip bookcase supports, for fast, efficient performance. Cuts the wider top rebates for the strip and the lowe...

Two flute TC cutter giving good chip clearance. Ideal for shallow lateral routing cuts such as recessing hinges. Corners will require final trimming square with a hand chisel or a corner chisel. Dimensions: D=5/8 inch D=15.9 mm C=19 mm OL=51 mm Sh...

Two flute TC cutter giving good chip clearance. Ideal for shallow lateral routing cuts such as recessing hinges. Corners will require final trimming square with a hand chisel or a corner chisel. Dimensions: D=3/4 inch D=19.1 mm C=19 mm OL=51 mm Sh...

Purpose made for stair housing jigs. Ensures tight fit of tread in string. Dimensions: D=13.5 mm C=20 mm OL=65 mm A=95 degrees Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 13.5 Cut Length Metric: 20 Overall Length Metric: 65 ...

Purpose made for stair housing jigs. Ensures tight fit of tread in string. Dimensions: D1=3/4 inch D1=19 mm C=25.5 mm OL=65 mm A=95 degrees Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Imperial: 3/4 Diameter Metric: 19 Cut Length Metr...