|
Trend |
TREND 4/85X1/2TC TWO FLUTE 28MM DIA X 25MM CUT |
Product Code: 4/85X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 7/64 inch
D=28 mm
C=25 mm
OL=66 mm
Shank Diameter=1/2 inch
Shank...
|
TREND 4/8X1/2TC TWO FLUTE 25.4MM DIA X 25MM 257056 |
Product Code: 4/8X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 inch
D=25.4 mm
C=25 mm
OL=68 mm
Shank Diameter=1/2 inch
Shank Di...
|
TREND 4/90X1/2TC TWO FLUTE 31.7MM DIA X 25MM CUT |
Product Code: 4/90X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 1/4 inch
D=31.8 mm
C=25 mm
OL=67 mm
Shank Diameter=1/2 inch
Shan...
|
TREND 4/91X1/2TC TWO FLUTE 30MM DIA X 25MM CUT |
Product Code: 4/91X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 3/16 inch
D=30 mm
C=25 mm
OL=67 mm
Shank Diameter=1/2 inch
Shank...
|
TREND 4/92X1/2TC TWO FLUTE 40MM DIA X 25MM CUT |
Product Code: 4/92X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 37/64 inch
D=40 mm
C=25 mm
OL=66 mm
Shank Diameter=1/2 inch
Shan...
|
TREND 4/94X1/2TC TWO FLUTE 44.5MM DIA X 32MM CUT |
Product Code: 4/94X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 3/4 inch
D=44.5 mm
C=32 mm
OL=73 mm
Shank Diameter=1/2 inch
Shan...
|
TREND 4/96X1/2TC TWO FLUTE 50MM DIA X 25MM CUT |
Product Code: 4/96X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 31/32 inch
D=50 mm
C=25 mm
OL=63 mm
Shank Diameter=1/2 inch
For s...
|
TREND 4/9X1/2TC TWO FLUTE 28.5MM DIA X 25MM CUT |
Product Code: 4/9X1/2TC TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Has a TCT plunge centre tip.
Dimensions:
D=1 1/8 inch
D=28.5 mm
C=25 mm
OL=67 mm
Shank Diameter=1/2 inch
Shan...
|
TREND 40/13X1/2TC B/GUIDED OVOLO 6.3MM RAD 3.2MM STEP |
Product Code: 40/13X1/2TC Supplied with alternative bearings to produce a rounding over and two sizes of ovolo moulding.
The smaller bearing gives a 3.2mm quirk.
Dimensions:
D=28.7 mm
C=13.0 mm
B=9.5 mm
B2=12.7 mm
B3=16.0 mm
R=1/4 inch
R=6.3 mm
OL=60 mm
Shank Diameter=1/2 ...
|
TREND 40/13X1/4TC B/GUIDED OVOLO 6.3MM RAD 3.2MM STEP |
Product Code: 40/13X1/4TC Supplied with alternative bearings to produce a rounding over and two sizes of ovolo moulding.
The smaller bearing gives a 3.2mm quirk.
Dimensions:
D=28.7 mm
C=13.0 mm
B=9.5 mm
B2=12.7 mm
B3=16.0 mm
R=1/4 inch
R=6.3 mm
OL=58 mm
Shank Diameter=1/4 ...
|
TREND 40/14X1/2TC B'GUIDED OVOLO 9.5MM RAD 3.2MM STEP |
Product Code: 40/14X1/2TC Supplied with alternative bearings to produce a rounding over and two sizes of ovolo moulding.
The smaller bearing gives a 3.2mm quirk.
Dimensions:
D=35.0 mm
C=16.0 mm
B=9.5 mm
B2=12.7 mm
B3=16.0 mm
R=3/8 inch
R=9.5 mm
OL=63 mm
Shank Diameter=1/2 ...
|
TREND 40/14X1/4TC B/GUIDED OVOLO 9.5MM RAD 3.2MM STEP |
Product Code: 40/14X1/4TC Supplied with alternative bearings to produce a rounding over and two sizes of ovolo moulding.
The smaller bearing gives a 3.2mm quirk.
Dimensions:
D=35.0 mm
C=16.0 mm
B=9.5 mm
B2=12.7 mm
B3=16.0 mm
R=3/8 inch
R=9.5 mm
OL=66 mm
Shank Diameter=1/4 ...
|
TREND 40/15X1/2TC B'GUIDED OVOLO 12.7MM RAD 3.2MM STE |
Product Code: 40/15X1/2TC Supplied with alternative bearings to produce a rounding over and two sizes of ovolo moulding.
The smaller bearing gives a 3.2mm quirk.
Dimensions:
D=44.0 mm
C=19.0 mm
B=9.5 mm
B2=12.7 mm
B3=16.0 mm
R=1/2 inch
R=12.7 mm
OL=67 mm
Shank Diameter=1/2...
|
TREND 40/16X1/2TC B'GUIDED OVOLO 15.9MM RAD 3.2MM SET |
Product Code: 40/16X1/2TC Supplied with alternative bearings to produce a rounding over and two sizes of ovolo moulding.
The smaller bearing gives a 3.2mm quirk.
Dimensions:
D=48 mm
C=22 mm
B=9.5 mm
B2=12.7 mm
B3=16.0 mm
R=5/8 inch
R=15.9 mm
OL=68 mm
Shank Diameter=1/2 inc...
|
TREND 41/5X1/4TC GUIDED 3F 45 DEG CHAMFER X 11MM CUT |
Product Code: 41/5X1/4TC Three flutes for extra fine finish.
Ideal for newel posts and caps for stairs.
Supplied with one bearing.
Dimensions:
D1=34 mm
C=11 mm
B=12.7 mm
A=45 degrees
OL=50 mm
Shank Diameter=1/4
Shank Diameter: 1/4
Diameter Metric: 34
Cut Length Metric:...
|
TREND 421/35X1/4TC HINGE SINKING 35MM DIA 253364 |
Product Code: 421/35X1/4TC These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type without scribers are for laminate covered boards.
Dimensions:
D=35 mm
OL=65 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter...
|
TREND 421/35X3/8TC HINGE SINKING 35MM DIA |
Product Code: 421/35X3/8TC These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type without scribers are for laminate covered boards.
Dimensions:
D=35 mm
OL=65 mm
Shank Diameter=3/8 inch
Shank Diameter: 3/8
Diameter...
|
TREND 46/010X1/4TC ROTA-TIP TRIMMER 12.7MM X 20MM |
Product Code: 46/010X1/4TC Blades can be rotated by exchanging blades over.
Dimensions:
D=12.7 mm
C=20 mm
OL=60 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Imperial: 1/2
Diameter Metric: 12.7
Cut Length Metric: 20
Overall Length Metric: 60...
|
TREND 46/01X1/4TC ROTATIP TRIMMER 12.7MM DIA X 8MM |
Product Code: 46/01X1/4TC Blades of cutters can be rotated through 180 degrees to give one new cutting edge.
Dimensions:
D=1/2 inch
D=12.7 mm
C=8 mm
OL=57 mm
B=12.7 mm
A=90 degrees
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Imperial: 1/2
Diameter Metric: 12.7
...
|
TREND 46/02X1/4TC ROTA-TIP A=90¡ X 19MM DIA X12MM CUT |
Product Code: 46/02X1/4TC Blades that can be rotated in 90 degree increments giving three extra new edges.
Dimensions:
D=19 mm
C=12 mm
B=19 mm
A=90 degrees
OL=52 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Metric: 19
Cut Length Metric: 12
Overall Length Metri...
|
TREND 46/03X1/2TC ROTA-TIP A= 90¡ X 19MM DIA X 30MM C |
Product Code: 46/03X1/2TC Blades of cutters can be rotated through 180 degrees to give one new cutting edge.
Dimensions:
D=19 mm
C=30 mm
B=19 mm
A=90 degrees
OL=78 mm
Shank Diameter=1/2 inch
Shank Diameter: 1/2
Diameter Metric: 19
Cut Length Metric: 30
Overall Length M...
|
TREND 46/03X1/4TC ROTA-TIP A= 90¡ X 19MM DIAX30MM CUT |
Product Code: 46/03X1/4TC Blades of cutters can be rotated through 180 degrees to give one new cutting edge.
Dimensions:
D=19 mm
C=30 mm
B=19 mm
A=90 degrees
OL=70 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Metric: 19
Cut Length Metric: 30
Overall Length M...
|
TREND 46/05X1/4TC GUIDED TRIMMER 6.35MM X 12.7 257113 |
Product Code: 46/05X1/4TC Two flute mini-trim with guide bearing will profile intricate shapes.
Max. 2.0mm trimming.
Ideal for acrylic trimming.
Dimensions:
D=1/4 inch
D=6.3 mm
C=1/2 inch
C=12.7 mm
OL=61 mm
B=6.3 mm
A=90 degrees
Shank Diameter=1/4 inch
Shank Diameter: 1/4...
|
TREND 46/06X1/4TC COMBI TRIMMER A1=90¡ X A2=45¡ |
Product Code: 46/06X1/4TC A self-guided combination trimmer.
A 90 degree trim is obtained by engaging the bottom half.
A 45 degree trim is obtained by lowering the cutter.
A fine height adjuster is recommended when using this cutter.
A larger 20mm bearing will spread t...
|
TREND 46/07X1/4TC GUIDED TRIM 6.3 DIAX25.4MM C 257114 |
Product Code: 46/07X1/4TC Two flute mini-trim with guide bearing will profile intricate shapes.
Max. 2.0mm trimming.
Ideal for acrylic trimming.
Dimensions:
D=1/4 inch
D=6.3 mm
C=25.4 mm
OL=75 mm
B=Fractionally larger than cutter dia mm
A=90 degrees
Shank Diameter=1/4 inch...
|
TREND 46/090X1/2TC GUIDED PROFILER 19.05MM X 63MM CUT |
Product Code: 46/090X1/2TC Profiler with shank mounted bearing guides.
For use with router mounted above or below a table when following a template.
For profiling and rebating applications only.
Not for plunge cutting/grooving.
A 3mm maximum overlap should be left before...
|
|
|