Trend

Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Dimensions: D=32 mm C=15 mm C2=22 mm A=45 degrees OL=66 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 32 Cut L...

Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Dimensions: D=40 mm C=19 mm C2=26.5 mm A=45 degrees OL=71 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 40 Cut...

Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Dimensions: D=51 mm C=25 mm C2=35 mm A=45 degrees OL=82 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 52 Cut L...

Use for producing mortar grooves and for bevelling applications. Dimensions: D=41 mm C=22.5 mm C2=23 mm A=45 degrees OL=62.5 mm Bottom flat diameter = 8.8mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 41 Cut Length Metric: 22.5 ...

Especially designed bevel cutter for routing Corian and similar luxury 'marble like, material which is used in many bathrooms and kitchens. Dimensions: D=24 mm C=25 mm A=75 degrees OL=65 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metr...

Two flute straight cutter with 3 degree taper. Designed for constructing wooden vacuum forming moulds. Tapered sides will allow the mould to release easily. Dimensions: D=12.7 mm C=32 mm OL=80 mm A=87 degrees Shank Diameter=1/2 inch Shank Diamet...

Use for producing mortar grooves and for bevelling applications. Dimensions: D=38 mm C=27 mm C2=25.5 mm A=60 degrees OL=62.5 mm Shank Diameter=1/2 inch Flat produced=12.5mm Shank Diameter: 1/2 Diameter Metric: 38 Cut Length Metric: 27 Overall Le...

To increase gluing area producing a strong joint in drawer production. Dimensions: D=25.4 mm C=12.7 mm OL=49 mm Shank Diameter=1/2 inch Timber thickness min.=15 mm Timber thickness max.=25 mm For stationary machines at max. recommended speed 24,000 ...

To rout butterfly key and splines in timbers and man-made boards. Use in conjunction with 104 deg (14 deg) dovetail cutter ref. L120 which cuts dovetail pocket. Use in a router table. Cut material in two passes to create a butterfly shape, width of...

Machining of this joint is carried out by routing one piece with the inside face on the table. The matching corner inside face is machined upright against the fence. Make sure that the cutter is centred on the workpiece. The cutter can also be u...

These machine bits have two wings, two scribers and a centre point. Tungsten carbide tipped for extensive drilling of particle boards, and plastics of soft to medium density. The scribe gives a very clean entrance hole. Not for use on hard dense m...

These machine bits have two wings, two scribers and a centre point. Tungsten carbide tipped for extensive drilling of particle boards, and plastics of soft to medium density. The scribe gives a very clean entrance hole. Not for use on hard dense m...

These machine bits have two wings, two scribers and a centre point. Tungsten carbide tipped for extensive drilling of particle boards, and plastics of soft to medium density. The scribe gives a very clean entrance hole. Not for use on hard dense m...

These machine bits have two wings, two scribers and a centre point. Tungsten carbide tipped for extensive drilling of particle boards, and plastics of soft to medium density. The scribe gives a very clean entrance hole. Not for use on hard dense m...

These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type with scribers is used on veneered and wood finishes. Use with pillar drills only. Dimensions: D=35 mm OL=65 mm Shank Diameter=1/4 inc...

These machine bits are typically used by kitchen furniture manufacturers for recessing circular hinges. This type with scribers is used on veneered and wood finishes. Use with pillar drills only. Dimensions: D=35 mm OL=65 mm Shank Diameter=3/8 inc...

These specially designed machine bits have a specially designed form of scriber to allow use at high speeds. For recessing circular hinges. For accurate repetitive routing, a template and guide bush fitted to the router base should be used. Dimens...

These specially designed machine bits have a specially designed form of scriber to allow use at high speeds. For recessing circular hinges. For accurate repetitive routing, a template and guide bush fitted to the router base should be used. Dimens...

These specially designed machine bits have a specially designed form of scriber to allow use at high speeds. For recessing circular hinges. For accurate repetitive routing, a template and guide bush fitted to the router base should be used. Dimens...

Ideal for fast chamfering. Popular in the sign making trades. For chamfering edges of plastic material. Dimensions: C=10 mm C2=14 mm P=5.5 mm A=45 degrees OL=53.5 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Metric: 25 Cut Length M...

Useful for bevelling thick timbers. Certain sizes can be used for jointing, boxes, pilasters and carcassing. Ideal for use by wood turners with smaller routers to create staves on 25mm stock. For full bevels, template should be fitted to compon...

Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Is ideal for imitating 'V' jointed tongue and groove on man-made board. Dimensions: D=22.28 mm C=6 mm C2=12 mm A=30 degrees OL=54.5...

Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Dimensions: D=22.28 mm C=6 mm C2=12 mm A=30 degrees OL=54.5 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Metric: 22.28...

Template thickness should be at least 5mm thicker than cutter cut length of cutter. Approximately 1.0mm flat will be found on the nose. Dimensions: D=1/2 inch D=12.7 mm C=16 mm B=12.7 mm A=60 degrees OL=66.61 mm Shank Diameter=1/4 inch Shank Diame...

Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Dimensions: D=11 mm C=5.0 mm C2=7.7 mm OL=54.5 mm A=45 degrees Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 11 ...

Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Dimensions: D=11 mm C=5.0 mm C2=7.7 mm OL=52.5 mm A=45 degrees Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Metric: 11 ...